304 or 201? The right stainless steel for wet areas
5 min read
What makes steel stainless?
Stainless steel is the general name for iron alloys that contain at least roughly 10.5 percent chromium. The chromium reacts with oxygen in the air and forms an invisible, extremely thin chromium oxide layer on the surface. That layer shields the steel, and when the surface is scratched it rebuilds itself quickly wherever oxygen is present.
So stainless steel is not a material that never rusts. It resists rust as long as its protective layer keeps renewing itself. How strong that layer is depends on the alloy, meaning the share of chromium, nickel and other elements. This is exactly where 304 and 201 part ways.
On the first day, a bathroom accessory or a dispenser can look identical in either grade. A polished or satin finish shines the same. The difference shows up over months of humidity, cleaning products and heavy use.
304 and 201 in plain words
304 is the most widely used stainless steel grade in the world. A typical 304 contains about 18 percent chromium and 8 percent nickel, which is why it is often called 18/8. Nickel helps keep the chromium oxide layer stable and makes the steel easier to form.
In 201, part of the nickel is replaced with manganese and nitrogen, and the chromium content is usually a little lower than in 304. Nickel is expensive, so 201 costs less, which is why it appears in products where price comes first.
In short, the two grades belong to the same family but do not do the same job equally well. The less chromium and nickel there is to feed the protective layer, the less the steel can take in demanding conditions.
- 304: more chromium and nickel, higher corrosion resistance, the usual choice for wet areas
- 201: manganese replaces part of the nickel, lower cost, more limited resistance in humid and chlorinated places
- Appearance: both grades can look the same when new; the difference appears over time
Why the difference matters in wet areas
Bathrooms, toilets, showers and kitchens are tough places for stainless steel. The air stays humid, water splashes onto surfaces and is often left to dry on its own. Some cleaning products contain chlorine, and in many places the tap water itself carries chlorine and minerals.
Chloride ions attack the weakest spots of the chromium oxide layer. When the layer is not strong enough, small stains appear first and, over time, tiny pits can form. With its higher chromium and nickel content, 304 holds up against this kind of attack far better than 201.
Traffic counts as well. In a washroom used by hundreds of people a day, accessories are cleaned often, touched often and stay damp. A small saving on material grade in such a place can soon come back as products that look stained and worn.
Is the magnet test reliable?
A common tip says that if a magnet does not stick, the steel is good stainless. It is not a reliable way to tell grades apart. In their annealed state both 304 and 201 are usually only very weakly magnetic or not magnetic at all, so a magnet cannot separate them.
On top of that, 304 can become slightly magnetic after cold working such as bending, pressing or cutting. If a magnet clings a little at the bend of a towel rail, that does not mean the material is poor. Equally, a magnet that does not stick at all proves nothing about the grade.
Only a chemical analysis identifies a grade with certainty. For everyday buying decisions, the practical route is simply to ask the supplier which grade you are getting.
Ask for the grade in writing
Saying that a product is stainless is not enough on its own; the grade is what matters. When you ask for a quote, make sure the material grade is written in the product description or in the quote itself. If the same product comes in different grades, confirm which one is being offered.
Sometimes only the housing of a product is stainless steel, while the pump, bowl, hinge or lock are made of other materials. That is not a flaw, but reading the whole description tells you what you are actually buying.
- Does the product description name the steel grade, for example 304 or 430?
- Is the whole product stainless steel, or only the housing?
- Are finishes such as polished and satin offered in the same grade?
When 201 can do, and when to prefer 304
201 can be a reasonable choice in dry areas with light use. Indoors, where humidity is low, surfaces rarely get wet and no harsh cleaners are used, such as an office corridor or a dry storeroom, a 201 product may look fine for a long time.
In humid and chlorinated settings such as bathrooms, toilets, showers, kitchens, pool surroundings and buildings near the sea, 304 should be the choice. There, products are in constant contact with water and cleaning products. In busy public washrooms, the extra resistance of 304 also helps products keep looking tidy for longer.
The final decision depends on the conditions on site, the expected service life and the budget. But when a wet area is involved, choosing the right grade from the start is usually easier than replacing products later.
At ALVO
152 of the 186 product descriptions in our range name 304 grade stainless steel. Some models use 430 grade, and some bathroom accessories use zamak, brass or aluminium; the material of every product is stated in its own description. Browse our accessibility equipment, the Hotel Series and every other category on the products page, and send your grade questions to us on WhatsApp.




